4B AA Nylathane™ Elevator Bucket
Industrial Duty Elevator Bucket
AA43/NY, AA54/NY, AA64/NY, AA74/NY, AA75/NY, AA85/NY, AA95/NY, AA96/NY, AA106/NY, AA116/NY, AA126/NY, AA127/NY, AA147/NY, AA148/NY, AA168/NY, AA188/NY, AA208/NY, AA228/NY, AA248/NY, AA1810/NY, AA2010/NY, AA2210/NY, AA2410/NY

High performance, severe duty AA style Nylathane™ bucket with reinforced front lip for unsurpassed impact and abrasion resistance, featuring unique anti-static and non-stick properties that make it suitable for light to heavy, free-flowing to sticky, abrasive industrial materials.

AA Nylathane elevator bucket
Product Features
  • Reinforced front lip
  • Excellent wear resistance
  • Excellent impact strength (Izod – 20 KJ/m2)
  • Self-cleaning surfaces
  • 75% lighter than fabricated steel
  • Anti-Static (108 Ohms)
  • Non-sparking & non-corroding
  • Service Temperature: Long term -40 to +110°C (with short peaks of 150°C)
  • Suitable for light to heavy abrasive industrial products, such as sand, aggregate, cement, wood chips and fertilizer.
Material
Nylathane™
Use by Industry
Industrial
Use by Product
Sticky Materials,
Light Industrial,
Heavy Industrial
    AA Nylathane elevator bucket - drawing
    AA Nylathane Nominal size A B C D T Weight Capacity (L)
    bucket (mm) (mm) (mm) (mm) (mm) (mm) (kg) Z3 (water)
    AA43/NY 110 x 80 104 78 79 52 5 37 0.1 0.21
    AA54/NY 130 x 100 135 106 106 74 5 35 0.25 0.55
    AA64/NY 150 x 100 160 106 106 74 5 35 0.29 0.67
    AA74/NY 180 x 100 185 106 106 74 5 35 0.32 0.79
    AA75/NY 180 x 130 184 135 134 95 8 35 0.47 1.26
    AA85/NY 200 x 130 210 135 134 95 8 35 0.52 1.46
    AA95/NY 230 x 130 236 135 134 95 8 35 0.57 1.66
    AA96/NY 230 x 150 238 165 160 108 8.5 37 0.86 2.21
    AA106/NY 250 x 150 264 165 160 108 8.5 37 0.94 2.5
    AA116/NY 280 x 150 290 165 160 108 8.5 37 1.02 2.78
    AA126/NY 300 x 150 316 165 160 108 8.5 37 1.09 3.07
    AA127/NY 300 x 180 316 184 184 126 8 36 1.33 4
    AA147/NY 350 x 180 367 184 184 126 8 36 1.5 4.75
    AA148/NY 350 x 200 365 210 210 143 10 37 2.32 5.7
    AA168/NY 400 x 200 416 210 210 143 10 37 2.6 6.6
    AA188/NY 450 x 200 467 210 210 143 10 37 2.9 7.5
    AA208/NY 500 x 200 517 210 210 143 10 37 3.14 8.44
    AA228/NY 550 x 200 568 212 211 143 12 37 3.65 9.35
    AA248/NY 600 x 200 619 212 211 143 12 37 3.93 10.26
    AA1810/NY 450 x 250 466 260 260 170 12.5 37 4.37 11.02
    AA2010/NY 500 x 250 517 260 260 170 12.5 37 4.77 12.37
    AA2210/NY 550 x 250 568 260 260 170 12.5 37 5.19 13.73
    AA2410/NY 600 x 250 619 260 260 170 12.5 37 5.6 15.08

    Mounting holes an venting to customer specification.

    *Standard AA buckets are beige; black buckets available on special request

    FAQ - Elevator Buckets

    FAQ - Elevator Buckets

    What is a HIGH EFFICIENCY elevator bucket?  
    HIGH EFFICIENCY elevator buckets incorporate all five of the following characteristics: a smooth interior front face with no "breaks", wing-less side walls, close vertical placement on the elevator belt, a tapered bottom and the ability to nest for shipping and storage.  For more details, CLICK HERE  
         
    Why use Low Profile elevator buckets?  
    Low profile elevator buckets are created to achieve the closest vertical spacing possible on the elevator belt, thereby optimizing the system for the greatest potential capacity.  Some styles of elevator bucket require modification and others are low profile by standard design.  Wet or sluggish inputs do not generally load and discharge well in low profile buckets.  Due to the extra capacity that is generated and the weight of the additional buckets and material, belt PIW rating, pulley shaft diameters and motor HP may have to be upgraded.  Check with 4B engineering department about the best way to get the most capacity out of your elevator leg.  
         
    Why add vent holes to the bottom of an elevator bucket?  
    When elevating fluffy or powdery materials, vent holes in the bottom of the elevator bucket allow it to fill and discharge more efficiently.  As material enters the bucket, it encounters a pillow of air resting in the bottom.  Vent holes provide an escape path for this pillow of air, so that the entering material does not bounce out of the bucket and back down the elevator leg casing.  Upon discharge, the vent holes allow air to re-enter the bucket at the material exits, releasing any vacuum that might hold it the bucket too long, creating down legging.  
         
    Are CC style elevator buckets interchangeable with Starco elevator buckets?  
    Starco elevator buckets have a special shallow geometry and are intended to be placed extremely close together on the elevator belt.  Therefore, you should check with the 4B engineering department before replacing Starco elevator buckets with any other brand or design.  
         
    How long of an elevator bolt do I need?  
    When installing buckets on an elevator belt, use this simple formula: 
    (belt thickness + bucket back thickness + washer thickness + nut thickness + 1/4 inch)  
         
     

    What is a "digger" bucket?  
    Some materials can form a hardened crust along the side wall of the elevator boot, and powders sitting over time can become rock hard.  Both of these issues can cause premature elevator bucket wear.  Digger buckets are designed to have slightly more width and projection than standard buckets, thereby "digging" through or breaking apart the hardened material, helping to prevent added wear to the standard buckets.  Digger buckets are traditionally made from steel, however nylon buckets may also be used depending on the application.  
         
    How many digger buckets do I need?  
    For most applications, use one digger bucket for every nine standard buckets.  
         
    Can I use buckets on an overlap splice?  
    An overlap splice doubles the thickness of the belt, so a bucket's projection will increase on the overlap.  Usually this will not cause a problem, but if it does, you can use buckets with one inch less projection or cut the tip of each bucket by half an inch on the spliced area.  
         
    When using an overlap splice, how much extra belt should I use for the splice?  
    The length of the splice should be three times the width of the belt.  
         
    How often should I replace head pulley lagging?  
    Lagging should be replaced every time the elevator belt is replaced.

    Bucket Elevator Design Service

    Bucket Elevator Design Service

    At 4B, we have designed hundreds of bucket elevators for all industries, including Animal Feed, Grain Handling, Flour Milling, Malting & Brewing through to Cement, Coal and other heavy industries.

    Take advantage of 4B's free, guaranteed worldwide technical support service from a team of engineers specialising in the design and calculation of bucket elevators.. Using your key technical data, our engineers can give you a detailed technical recommendation for the ideal bucket elevator with the ideal capacity and discharge characteristics. We can either design your new bucket elevator or we can help you to increase the capacity of your existing bucket elevator.

    To get a free bucket elevator calculation

    Please fill this form in as accurately as possible to allow us to deal with your enquiry more effectively. 

    At 4B, we have designed hundreds of bucket elevators for all industries, including Animal Feed, Grain Handling, Flour Milling, Malting & Brewing through to Cement, Coal and other heavy industries.

    Take advantage of 4B's free, guaranteed worldwide technical support service from a team of engineers specialising in the design and calculation of bucket elevators.. Using your key technical data, our engineers can give you a detailed technical recommendation for the ideal bucket elevator with the ideal capacity and discharge characteristics. We can either design your new bucket elevator or we can help you to increase the capacity of your existing bucket elevator.

    To get a free bucket elevator calculation

    Please fill this form in as accurately as possible to allow us to deal with your enquiry more effectively. 

    Contact Details

    Elevator Details

    If you would like to send us a technical drawing or document with your enquiry, please send to 4b-uk@go4b.com.

    CAPTCHA
    Den här frågan testar om du är en mänsklig besökare och förhindrar automatiska spaminsändningar.