Flight installation and chain assembly made easy !.
Touchswitch
Belt misalignment on an elevator is a problem that is difficult to solve because it needs to be adapted for each elevator and type of elevator.
4B Braime starts distribution of MLT belt fasteners
4B Braime has signed an agreement securing itself the exclusive distribution rights for MLT conveyor belt fasteners in the UK and Ireland.
MINET products, are backed by more than 50 years experience in the field of lacing systems, vulcanizing presses and special truly endless belts...
ATEX-approved for zones 20, 21 & 22
The Remote Auto-Set is a radio-frequency level indicator that allows single point level detection of most liquids and bulk granular materials such as powders, grain, sugar, cement etc…
The remote version allows the programming and monitoring to be achieved at a distance of up to 100 metres between the control module and the transponder....
4B to replace JACKSON BOLTS with Elevator Bolts made under the 4B Brand
4B BRAIME have purchased the stock, machinery and tooling to manufacture the range of elevator bucket bolts previously manufactured by JACKSON FASTENERS.
This is good news for all those companies who have run into sourcing problems after Flexco’s decision to stop manufacturing their range of JACKSON elevator bucket bolts....
Separators
A new range of magnetic separators has obtained the ATEX approval for the use in hazardous areas.
Inline Junction Box D5M
The best compromise for industrial and Dust Hazard explosive atmospheres ATEX certified for zone 20, 21 and 22
In explosive and industrial atmospheres it is often necessary to connect different types of cables when installing sensors. Traditionally, junction boxes were used for this but were often cumbersome and expensive.
Alternatively, it is not always possible to install ATEX connectors on the sensors themselves and in some cases this solution can become very costly.
The DM5 Inline Junction Box has been developed to overcome these problems. It is a compromise between a junction box and a proprietary connector for sensors.
THE NEW 4B SPS - SUPER STARCO INDUSTRIAL DUTY BUCKET
4B Components are pleased to announce the introduction of the industrial duty pressed steel SPS bucket into the North and South American markets.
AB400 Elite Elevator / Conveyor Belt Misalignment System
Detects dangerous misalignment of buckets and belt to prevent costly downtime and help eliminate the risk of explosions.
The AB400 Elite uses an electronic microprocessor control unit and up to 4 magnetic alignment sensors to monitor the alignment of the belts of 2 separate bucket elevators / conveyors. Alternatively the 4 sensors can monitor the top and bottom belt alignment in a single bucket elevator.
BAP2
New Alignment Sensor for Bucket Elevators
The BAP2 is a new, externally mounted non-contact alignment sensor reading through a polycarbonate window in the elevator case. The fail safe magnetic sensors remain unaffected by dust or product build up, continuously monitoring the moving target with visual indication by LED.
HotBus™ T500 Digital Monitoring System
Continuous Bearing Temperature and Belt Misalignment Monitoring System
The new HotBus™ Digital Serial Communication System from 4B offers customers a much simpler and more cost effective approach to continuous bearing temperature monitoring. With up to 256 bearing sensors on a single twisted pair cable, installation is much easier and maintenance free.
Bolt N Go
Drop Forged Conveyor Chain
Flight installation and chain assembly made easy! 4B Braime is pleased to announce the launch of the new revolutionary Bolt ‘N’ Go drop forged chain system.
Heavy Duty Stainless Steel Whirligig
If you are looking for the toughest solution to shaft speed monitoring, then the Heavy Duty Whirligig is the unit you need.
Watchdog "Elite" Bucket Elevator Monitor
The bucket elevator monitor for the 21st century.
The 4B Watchdog "Elite" uses non-contacting, magnetic sensors to monitor belt speed and belt alignment at the head / boot or both. Additional sensors monitor bearing temperature, head pulley alignment and plugged spout conditions. The system incorporates dual microprocessor control, using the latest PIC microprocessors and non-volatile (EEPROM) memory chips.
New FRASOR belt by 4B
4B BRAIME have launched the new “F.R.A.S.O.R.” belt to comply with increasing safety standards in the grain industry.
The name “F.R.A.S.O.R.” stands for Fire Retardant, Anti-Static and Oil-Resistant.
In addition to being anti-static and oil-resistant, the new belt’s most important feature is its flame retardant quality ISO 340: ...
ATEX certified (gas zone 1 and dust zone 20)
The P100 inductive sensor is designed for various purposes such as position indication or the generation of impulses for the detection of speed (elevator, belt, motor…) in explosive gas or dust atmospheres, without internal cabling. It has received the ATEX certification Ex II 2G 1D Eex m IIB T4 T100°C which allows it to be used in zone 20, 21 and 22 (dust) and zone 1,2 (gas).
ROTOSAFE - Rotary Level Indicator -- by 4B
4B introduces a new and improved Rotary Level Indicator. The ATEX approved RotoSafe incorporates two detection circuits. One circuit indicates when material has impeded the paddle, and the other circuit provides indication when the paddle stops turning, therefore making it a failsafe solution for high level or plug condition monitoring in bins, silos elevators or conveyors. Bonus features include user adjustable sensitivity, LED indication and a corrosion resistant housing. ...
Pullswitch - Conveyor Safety Stop Switch - by 4B
Taut wire Pullswitch provides “failsafe” emergency stop protection along the length of the conveyor. Compact double-ended design with five changeover relay contacts, allows shutdown of the conveyor if the cable is pulled or if the cable becomes slack. Internal snap-action trip inhibits conveyor re-start until the tripped Pullswitch is manually reset. High visibility flag indication and “cats eye” lens provides quick and simple location of the tripped Pullswitch under all conditions....
Stackable CC-S Style Elevator Buckets - by 4B
4B Braime has developed what is described as “the world’s first stackable CC-style polymer elevator bucket.” It is stackable in the sense that the buckets nest inside one another for reduced storage and shipping space and greater freight savings due to increased density and lower freight classification.
The unique patent-pending design includes tapered sides for improved filling and discharge, as well as the Iceberg Edge™, a thick front lip..
“WHIRLIGIG” ™ Three in One - by 4B
The “WHIRLIGIG”™ three in one target / bracket / guard is available for all industry standard cylindrical or DIN inductive sensors. The sensor bolts to the base plate and the complete assembly couples to the machines shaft. The installation of speed sensors is now simple and reliable. Shaft end float and machine vibration does not adversely affect the performance of the sensor, as the whole assembly moves with the shaft. ...
